2020澳门历史开奖记录

  

-
 
加速機電毛病緣由與辦法
 
毛病
Malfunction
緣由
Causes
辦法
Measures
在加速機的緊固件處有大的噪聲
High noise at tightening parts
緊固件松動了
Loose of tightening parts
將螺栓/螺母擰緊到劃定的扭矩。改換破壞了的螺栓/螺母。
Tighten nut bolt to correct state Replace damaged nut/bolt
加速機的噪聲變更
Changing noise
齒輪的輪齒產生了破壞
Teeth of gears get damaged
和客戶辦事部聯系。檢討壹切零件上的齒,改換破壞了的零件。
Consult after-sales department
Check teeth of gears and replace damaged one.
軸承間隙過大
Clearance of bearings too big
和售後辦事部聯系。
調劑軸承的間隙。
Consult after-sales department
Adjust the clearance of bearings
軸承破壞
Bearings get damaged
和客戶辦事部聯系。
改換破壞的軸承。
Consult after-sales department
Replace damaged bearings
軸承溫度降低
Bearing temperature rise
箱體外面的油面太高或太低
Oillevel is too high or low
在室溫下檢討油面的高度並按需加油。
Check oil level at room temperature and add on reduce oil
油過于陳腐
Oil is used too long
和售後辦事部聯系。
檢討前次換油的時光。
Consult after-sales department.
Check the date that oil be replaced last time.
油泵的機械毛病
Malfunction of oil pump
和售後辦事部聯系。
檢討油泵的任務能否正常,補綴或換新的油泵。
Consult after-sales department.
Check if pump works normally,repair or replace it.
軸承破壞
Bearing damage
和售後辦事部聯系。
-查閱操作人員在振動丈量中所取得的數據。
-檢討並按須要換軸承。
Consult after-sales department.
-Look up the date about vibration.
-Check and replace it on request.
任務溫渡過高
Working temperature too high
箱體外面的油面太高
Oil level is too high
檢討油面的高度,假如有需要的話,調劑。
Check oil level,and adjust if necessary.
油過于陳腐
Oil is used too long
和售後辦事部聯系。
檢討上一次換油的時光,假如有需要的話就改換。
Consult after-sales department.
Check the date that oil was replaced last time,
replace it if necessary
油遭到嚴重凈化
Oil is pollucted seriously
和售後辦事部聯系
-換油。
Consult after-sales department.
-Replace oil.
在裝備了光滑油冷卻體系的加速機上:冷卻劑的流量太低或許太高
Flux of cooling material is too high or low
周全調理出口和出口管道的閥門。
檢討水冷裝配的自在流量。
Adjust entrance and exit valves.
Check the flux of water cooling devices.
經由過程水冷裝配的油流太低,其緣由是:濾油器嚴重梗塞
Oil flux through water cooling devices is too low
清算濾油器
Clean oil filter
油泵的機械毛病
油泵破壞
Malfunction of oil pump
Oil pump damage
和售後辦事部聯系。
-檢討油泵的功效能否正常。
-補綴或許換新。
Consult after-sales department.
-Check of oil pump works normally.
-Repair or replace it.
在裝備了電扇的加速機上:電扇罩的空氣進口和/或箱體嚴重凈化
Entrance of fan shield and housing polluted seriously
清算電扇罩和箱體
Cleanse fan shield and housing.
裝備了冷卻螺旋管的加速機:冷卻螺旋管外面結垢
Redsidues in cooling coil
和售後辦事部聯系。
-清算或許改換螺旋管。
Consult after-sales department.
-Claen or replace cooling coil.
軸承處的振幅降低
Swing at bearing higher
軸承破壞
Bearing is damaged
和售後辦事部聯系。
-檢討並按需改換軸承。
Consult after-sales department
-Check and replace bearing.
齒輪破壞
Gear is damaged
和售後辦事部聯系。
-檢討並按需改換齒輪。
Consult after-sales department.
-Check and replaces gears.
止回裝配的溫渡過高
止回功效的生效
Temperature of anti-backstop too high and it becomes malfunction
止回裝配破壞
Anti-backstop becomes malfunction
和售後辦事部聯系。
-檢討並按需改換止回裝配。
Consult after-sales department.
-Replace anti-backstop
加速機漏油
Oil-leak of gear unit
箱體蓋或許聯接處的密封不良
Sealing at cover and connection not in good state
檢討密封和銜接處,假如需要的話,改換新的。將銜接處密封好。
Check air-proof and connection part,replace them if necessary,and seal up connection part.
徑向軸封生效
Shaft seal is malfunction
和售後辦事部聯系。
-換新的徑向密封環。
Consult after-sales department.
油中有水
Water in oil
油中有雜物
Mixer in oil
用試管檢討油的狀況能否有水份存在。
試驗室剖析油.
Classify if there is water in oil by using tube.
Analyse oil in laboratory.
光滑油冷卻器或許冷卻螺旋管生效。
Cooling coil is of mal-fanction
和售後辦事部聯系。
-找出並補綴泄露的地方。
-改換冷卻器或許螺旋管。
Consult after-sales department.
-Find out and repair leakage place.
-replace cooling coil
加速機遭到機械間透風過去的涼空氣而發生凝露
Cool air will cause water drop in gear unit.
用適合的保溫資料將加速機掩護起來。
封閉空氣的出口或許在構造上轉變其偏向。
Shelter gear units with proper
注:關於客戶本身沒法消除的毛病請和我公司售後辦事部聯系。
Note: Please consult after-sales department, if malfunction can not be removed by consumers tehmselves.
 
0

在線
客服

客服
熱線

-
7*24小時客服辦事熱線

存眷
微信

存眷官方微信
頂部

Copyright ©2018 REDSUN TIMES GROUP All Right Reserved

台灣瑞德森機械有限公司 版權壹切

全國同壹辦事熱線

-

2020澳门历史开奖记录